FAQ’s

Wood veneer edging roll can be used to edge (or replace edging) on cabinets, doors, drawers, counter tops, tables – basically any type of furniture or fixture with a panel edge.

It is general hard to get a precise colour match for wood veneer, given it is a natural product, with rolls varying in tone and grain from tree to tree. Consider treating the edging with a wood stain, varnish or oil to blend with other surfaces. Keep in mind that cabinet and furniture edging is often hidden, so consider how much effort is required for a precise match, vs. a close match, which should be achieved by choosing the right species of wood.

Our pre-glued edging will remain sticky but not set fully within the first 1-2 minutes, allowing for realignment, should this be necessary. We do recommend, prior to activating the glue, affix the edging in place with some masking tape. Thereafter, remove the masking tape on the section to be fixed, before ironing that section on.

Yes, our veneer edging can be painted, using any wood suitable paint. It can also be sanded, varnished, stained or be applied with wood oils.

Primer is recommended as wood veneer should be treated in the same manner as painting on any other wood surface.

This is not the ideal surface to apply the edge banding. We recommend first removing the paint (a scrapper, paint stripper, blow torch or sander will do this), and then sanding the under-surface in preparation for adhesion with the hot-melt glue.

An iron is not always the best tool for the job, like with tight corners or curved surfaces. Further, you might be concerned that the heat will damage a delicate edge / material underneath. In such circumstances, a simple hairdryer may be used to activate the hot-melt glue. We recommend using a cloth to press and fix the edge banding into place thereafter. A smaller, weighted item, such as a metal tumbler can be used to press on to curved edges. Do take care not to overheat and burn the edging (or your hands!).

If you need to apply to an area which encounters moisture, such as in the kitchen or bathroom, you can use our wood veneer edge banding, provided you coat the surfaces after application using an appropriate waterproof sealant or varnish.

Within reason, yes, provided the edging has been coated using an appropriate waterproof sealant or varnish.

Our wood edging is malleable to gentle curves and should suit a routed edge. The product only has so much ‘give’ so do test first to see if the edging will curve without cracking. For acute curves or angles, ensure you cut the edge banding and apply in sections.

The edge banding can be applied to any surface, the obvious choice being wood. It will adhere to metal and glass surfaces as well, but this may not suit an iron-on application. For wood surface preparation, a light sanding will suffice, to key the area prior to application.

For best results we recommend removing any old edge banding and replacing with fresh edging. If this is not possible, due to the old edging being heavily glued, sanding down to an even edge might do the trick.

The obvious answer is wood! However, it also receives a coat of hot-melt glue on the underside, and dependent on the wood species, sometimes fleece, which helps the wood to curve and roll.

The 7.5m length covers the linear edge of a standard MDF board (8' x 4' / 2440 x 1220mm). This roll size can help our customers purchase the right amount of edging, dependant on the job at hand.

Our standard widths for wood veneer edge banding are 15mm, 19mm, 22mm, 30mm, 40mm and 50mm. Custom widths can be produced, but this would depend on a bulk order, carrying a minimum linear meterage.

For best results, it is common practise to purchase a tape which is slightly wider than the edge being applied to. Thereafter, an edge trimmer should be used to peel off the remaining edges and lightly sanded for a smooth finish.

First measure the widest area of the edge. Then choose an edging roll which will cover this. Thereafter you can use an edge trimmer or craft knife to customise the edge as needed, not forgetting to sand to a fine finish. We offer pre-glued wood veneer edge banding between 15mm to 50mm width. We also offer unglued jumbo rolls of veneer at 135mm wide.

Wood edging will work on plywood. If the board edge has uneven areas, it should be prepped first using a wood filler and then sanding to create a smooth surface. Do check the filler applied can be heated slightly.

Wood edging will also work on chipboard. If the board has an uneven edge, it should be prepped first using a wood filler and then sanded to create a smooth surface. Do check the filler applied can be heated slightly.

As a real wood product, it would not be suitable for repair to plastic or laminate flooring. In general edge banding is designed to cover an edge. However, for a quick solution, you could try using wider (30-50mm) wood style melamine edge banding, which can be found here.